Public Knowledge Base
Contact Armstrong Flooring

Search

Home > Knowledge Search >
Back to Results

Armstrong Summit Select All-In-One Hardwood Adhesive "Product Information"

« Go Back
Caution / Warning
CAUTION:Slight skin and eye irritation is possible. Avoid skin or eye contact. Avoid breathing fumes and dusts. During handling, wear appropriate personal protection equipment such as safety glasses and gloves. Use only in a well ventilated area. Keep container closed. Do not take internally. If eye contact occurs, flush thoroughly with running water. If skin contact occurs, wash skin thoroughly with soap and water. If inhaled, move to fresh air. Consult a physician if symptoms develop and persist. For further information, refer to the Material Safety Data Sheet. Keep out of reach of children. Caution: During installation process, adequate ventilation of the work area should be maintained. Although the adhesive is low odor, persons who are sensitive to odors or chemicals should avoid the work area during installation.
MSDS
Product Attributes
 
    Type:
    Modified silane
      Color:
      Tan
        Taggants:
        None
          Trowel:
          V-notch: 1/4"D x 3/16"W x 5/16"A - Engineered Wood Flooring, Solid Wood Flooring, Laminate flooring
          Square notch: 3/32"D x 3/32"W x 3/32"A - Solid Wood Parquet
          Summit trowel: 1/4"D x 3/16"W x 1/2"A - All-in-one Application (Included with Summit Select adhesive)
            Open Time:
            None - Install wood flooring immediately after adhesive is spread.
              Working Time:
              Approximately 50-75 minutes
              Note: Open time may vary due to temperature, humidity, and porosity of subfloor
                Spread Rate:
                 
                User-added image
                Spread Rate
                Hardwood and Laminate
                V-Notch
                50-60 sq ft/gal
                Parquet
                Square Notch
                70-80 sq ft/gal
                All-in-one Application
                Summit Trowel
                30-35 sq ft/gal
                  Removal:
                  If adhesive is wet use warm soapy water. Remove dry adhesive with low odor mineral spirits or a solvent based adhesive remover that is compatible with the hardwood manufacturer's finish. Armstrong Summit Select Adhesive is easiest to remove in the wet state
                    Advantages:
                    • Premium moisture control
                    • No moisture testing required*
                      • No RH limit*
                    • One solution for all hardwood and laminate floors
                    • All-in-One Product
                      • Adhesive
                      • Sound diminisher - exceeds IIC & STC requirements*
                      • Moisture barrier*
                      • Crack isolation membrane*
                    • Can be used on wood floors of all thicknesses
                    • Saves time on installation
                    • Easy to trowel
                    • Easy clean up
                    • Exceeds IIC & STC sound requirements
                    • Low-VOC – no residual odor
                    • Non-Urethane formula
                    • Contains no solvents, water, isocyanates or hazardous ingredients
                    • 100% solids – you get all of what you pay for
                    • Rapid strength build
                    • Avoids a double-stick install
                                *When SummitTM trowel is used
                      Shelf Life:
                      Shelf life is one year if not opened and the container is stored at 70° F (21°C)
                      Freeze/Thaw StableWhile this adhesive is freeze-thaw stable it is necessary to protect it from freezing. Adhesive that has been exposed to cold temperatures must be allowed to acclimate to room temperature.
                        Available Units:
                        4-Gallon Pail
                          VOC:
                          VOC content 0.05 g/l; calculated and reported, SCAQMD 1168
                           
                          Sound Test Ratings w. 1/2" Engineered
                          IIC
                          STC
                          Delta IIC
                          With Ceiling
                          68
                          62
                          20
                          Order & Warehouse Information
                          Order and Warehouse Information
                          Language
                          English/French/Spanish
                          Size
                          4-gallon (15,14 L)
                          Carton Item No.
                          SUMTS418
                          Item UPC
                          042369 92615 7
                          Carton Weight
                          45.6 lbs
                          Items per Carton
                          Sold individually
                          Pails per Pallet
                          48
                          Substrates
                          • On, above, or below grade concrete
                          • Suspended wood and wood underlayments
                          • Existing well-bonded resilient flooring; (not perimeter-bonded or heavy cushion-backed)
                          • Properly mixed and applied powder cementitious underlayments
                          • Radiant-heated subfloors where the surface temperature does not exceed 85° F (29° C)(except for solid wood strip and plank)
                          • Primed, poured-in-place gypsum subfloors
                          • Ceramic
                          • Fully secured cork flooring and acoustic cork
                          • Aluminum
                          • Stainless steel
                          • Properly prepared terrazo
                          • Do not install over floating floors
                          Installation Procedures
                          Use:Residential, Commercial
                           For the interior installation of all types of wood flooring, including
                          • engineered hardwood
                          • pre-finished and unfinished solid hardwood flooring
                          • acrylic infused hardwood
                          • bamboo
                          • solid parquet hardwood
                          • laminate floors
                             


                          Preparation:
                          • Follow manufacturer's installation instructions before spreading the adhesive.
                          • Room and subfloor temperature must be a minimum of 65° F (18° C) and 95° F (35° C) with relative humidity between 35% and 55% for 72 hours prior, during and after installation is complete. Maintain a minimum temperature of 55° F (13° C) thereafter. The building must be enclosed with all outside doors and windows in place with permanent or temporary HVAC system in operation.
                          • All concrete slabs should be completely cured and dry.
                          • Wood substrate must have moisture content below 13% using a Tramex moisture meter.
                          • Subfloors must be flat to within 1/8" in 6 feet or 3/16" in 10 feet.
                          • All subfloors must be free of all foreign substances as well as concrete admixtures, grease, paint, dirt and alkali salts. Subfloors must be smooth and sound. All loose subfloor must be renailed or properly bonded to create a sound subfloor. 
                          • When installing 3/4" solid hardwood flooring, ensure all planks are straight.
                          • If using Armstrong Summit Select as a moisture/sound barrier and crack isolation membrane (for cracks up to 1/8" in width) in addition to installation, the concrete subfloor must be fully cured (at least 45 days), dry to touch and absorbent (drops of water must penetrate surface within 1 minute), and concrete surface must have a concrete surface profile (CSP) of 1-3. For installations that do not require moisture/sound barrier or crack isolation, the concrete subfloor moisture must be no more than 3 lbs/1,000 ft2/ 24 hours (using a calcium chloride test kit according to ASTM F-1869 test method), and no more than 75%RH (tested in accordance with ASTM F-2170). 
                          • Note: The Summit Select application trowel blade included in the pail must be used to apply the moisture barrier and installation coat of adhesive.
                          • Note: For best application, replace the Summit trowel every 200-300 square feet of adhesive applied.
                          Installation:
                          • Spread adhesive using recommended trowel.
                          • Installation of the wood should begin immediately.
                          • Press wood into adhesive. Occasionally check the back of a board for 100% adhesive transfer.
                          • Roll floor with 100 lb. roller immediately following installation.
                          • Avoid foot traffic for 16 hours after installation and furniture may be lifted into place after 24 hours.
                          • Do not apply finishes to unfinished products until adhesive is properly cured.
                          Clean-Up
                          • Remove wet adhesive with warm soapy water. If dry remove adhesive with low odor mineral spirits or a solvent based adhesive remover that is compatible with the hardwood manufacturer's finish.
                          • Armstrong Summit Adhesive is easiest to remove in the wet state

                          Clean trowels frequently with a clean dry cloth to prevent debris and adhesive buildup.
                          LEED / Environmental
                          Warranty
                          This product is manufactured according to exacting quality control standards and is warranted to be free from manufacturing defects. Defective materials called to our attention within one year of manufacture will be replaced. No guarantee, expressed or implied, is made regarding the performance of this product since the manner and conditions of application are beyond our control. For complete warranty details or to obtain an SDS for the product, contact Customer Service at 800 233 3823
                          Product Image
                          User-added image
                          Information