Armstrong Flooring S-202 Static Dissipative Tile (SDT) Adhesive DATA SHEET


Caution Eye and Skin Irritant


S-202 Static Dissipative Tile (SDT) Adhesive SDS

For Use With

Product Information

Copper (Alloy 110) grounding strips supplied with adhesive. A see-through, self-adhering envelope is taped to the top of the lid of the pail.

4 gallon pails contain 2 each copper grounding strips, 2″ wide x 12′ long. The thickness is .003″.

1 gallon pails will contain 1 copper strip 2″ wide x 6′ long with a thickness of .003″.

*1 Gallon copper strip package is now available for order if extra copper strips are desired. See Carton/Pallet Table below.

TypeWater-based resin
TrowelFine notch (1/32″ deep, 1/16″ wide, 5/64″ apart), U-notch
CoverageApproximately 150 sq. ft. /gal. (14 sq. m)
Units1 gallon (3.78 L) and 4 gallon (15.14 L)
Open TimeUntil dry to touch; 60 minutes or more
Working TimeUp to 6 hours (working times may vary based on job conditions, substrates, temperature and humidity)
RH (ASTM F2170)75%
pH5 to 9
MVER (ASTM F1869)3lbs/1000 sq ft /24 hours
Shelf Life1 year, unopened
Freeze/Thaw StableNo, keep from freezing
VOC Content< 50 g/L; calculated and reported, SCAQMD 1168
Clean UpWet or Dry- clean, white cloth and mineral spirits
SubfloorsAll grade levels of concrete and suspended wood.
Ceramic, terrazzo, polymeric poured and certain metal subfloor when properly prepared with S-194
Radiant Heated subfloors where the surface temperature does not exceed 85° F (29° C)
AdvantagesMoisture and alkali resistant
Long working time (up to 6 hours)
Manufacturing LocationUSA
Size1-gallon (3,78L)4-gallon15.14L
Carton Item No.1-gallon (3,78L) – 002021084-gallon – 0020241815.14L – S-202605
Item/Carton UPC1-gallon (3,78L) –
4-gallon –
042369070591 (order individually)
15.14L –
042369082426 (order individually)
1-gallon (3,78L) –
8” L x 8” W x 8” H
4-gallon –
13” L x 13” W x 12.5” H
15.14L –
13” L x 13” W x 12.5” H
Carton Weight1-gallon (3,78L) – 10 lbs.4-gallon – 37.17 lbs.15.14L – 16.86 kg
Items per Carton1-gallon (3,78L) –
Containers sold individually
4-gallon –
Containers sold individually
15.14L –
Containers sold individually
Cartons per Pallet1-gallon (3,78L) – 1004-gallon – 4815.14L – 48
Additional Copper Strips (1) Strip 2″ wide x 6’ long-
(1) Strip 2″ wide x 6′ long-


When Armstrong Flooring S-202 is used with a recommended Armstrong floor application, the Armstrong Guaranteed Installation System warranty applies.


FloorScore Certificates – Adhesives
LEED Credits: EQ 4.1
Sustainable Design Information
LEED Credit Information – Installation Products 

Recommended Substrates

Will bond to all substrates listed below, but refer to the flooring installation system for specific installation recommendations:

DO NOT USE OVER: Concrete with excessive moisture and/or alkali; existing resilient flooring; substrates treated with fire-retardant chemicals, fungicides, preservatives, release agents, adhesive removers, sealers, curing compounds or other incompatible treatments

Application Instructions

  • Condition area to be installed, adhesive, and tile at 65° F (18° C) or above for 48 hours before, during, and for 48 hours after installation.
  • Subfloor must be smooth, sound, dry, clean, and free of dirt, wax, polish, paint, and all other foreign matter which may interfere in a good bond, including curing agents and sealers.
  • Always run a moisture and alkali tests over concrete on any grade level or any other substrate over on- or below-grade concrete. For accurate results, curing agents must be removed in areas where tests will be run. Moisture test results should not exceed 3 pounds/1000 sq ft/24 hours for a calcium chloride test or 75% for a relative humidity in-situ probe test. Alkali readings should be 5 to 9.
  • Stir any liquid on the surface into the adhesive and full spread using the recommended trowel notching.
  • Allow adhesive to set open until dry to the touch, approximately 60 minutes. When dry to the touch, the adhesive will be tacky with no transfer to fingers.
  • Install and fit all tile within 6 hours. Working time will vary based on job conditions, substrate, temperature and humidity.
  • Place 18 inches of the copper grounding strips into the adhesive at predetermined locations. Allow 6 inches to protrude from the edge of the floor up the wall so the strip can later be connected to a ground. Cover the part of the strip that’s been placed in the adhesive with more adhesive.
  • Allow the adhesive on the copper grounding strips to dry to the touch and then install the tile over the strips.
  • Roll tile in both directions with a 100-pound roller.
  • Use mineral spirits to remove wet or dried adhesive residue carefully following warnings on container.
  • Do not wet wash or strip tile for at least five days after installation.

Product Image

Updated on August 31, 2023