Armstrong Flooring S-725 Wall Base Adhesive DATA SHEET

Contents

Precaution

Caution Eye and Skin Irritant
Stir well before using

Language	English/Spanish
Size	Gallon 4 Gallon 30 oz Cartridge
Carton Item No.	Quart: 00725124 (Disc. 9/15) Gallon: 00725408 4 Gallon: 00725418 30 oz Cartridge: 00725125
Item/Carton UPC	Quart: 0-42369-00752-8 (Disc. 9/15) Gallon: 0-42369-10920-8 4 Gallon: 0-42369-07066-9 30 oz Cartridge: 0-42369-10921-5
Carton Dimensions	Quart: N/A (Disc. 9/15) Gallon: 15.5″ L x 15.5″ W x 8.5″ H 4 Gallon: 13″ L x 13″ W x 12.5″ H 30 oz Cartridge: 8.5″ L x 10.75″ W x 17″ H
Carton Weight	Quart: N/A (Disc. 9/15) Gallon: 42.15 4 Gallon: 41.96 30 oz Cartridge: 30.63
Items per Carton	Quart:12 qts/ctn (Disc. 9/15) Gallon: 4 gallons/ctn 4 Gal: 1 pail 30 oz. cartridge: 12 cartridges/ctn
Cartons per Pallet	Quart: 40 ctns (Disc. 9/15) Gallon: 30 ctns 4 Gallon: 48 pails 30 oz Cartridge: 60 ctns

When Armstrong S-725 is used with a recommended Armstrong floor application, the Armstrong Guaranteed Installation System warranty applies.

Will bond to all substrates listed below but refer to flooring installation system for specific installation recommendations:

DO NOT USE OVER:

INSTALLATION TIPS: Refer to Wall Base Installation System.

Condition area to be installed, materials, and adhesive at 65° F (18° C) or above for 48 hours before and 48 hours after installation.
Substrate must be smooth, sound, dry, clean, and free of dirt, wax, polish, loose paint, and all other foreign matter which may interfere in a good bond, including curing agents and sealers.
Glossy surfaces must be abraded for a proper bond.
Stir any liquid on the surface into the adhesive.
Use recommended trowel notching to spread adhesive on the back of cove base or directly to the substrate. Stay 1/8″ away from the top of the base to prevent adhesive oozing. (When using cartridges, apply beads uniformly spaced on the back of the cove base: two 1/8″ beads to the back of 2-1/2″ base, three beads to 4″ base, and five beads to 6″ base.)
Install cove base immediately.
Press firmly to the wall. To assure a tight fit, roll the cove base toward previously installed section.
Remove wet adhesive residue with a clean, white cloth dampened with soapy water. Use mineral spirits for dried adhesive residue carefully following warnings on container.

Updated on October 4, 2024

Type	Water-based/rubber-resin
Color	Off-white
Taggants	Yes – 50% Yellow and 50% Orange
Trowel	1/16” deep, 1/16” wide, 3/32” apart, U-notch
Coverage	2-1/2″ Wall base: 375-425 lin. ft./gal (114-130 m. lin.) 4” Wall base: 300-350 lin. ft./gal (91-107 m. lin.) 6” Wall base: 200-250 lin. ft./gal (61-76 m. lin.) 7” Riser: 200-250 lin. ft./gal (61-76 m. lin.) 30-oz cartridge– 50 lin. ft. (15.24 lin. m) per 30 oz. Cartridge (3) 1/8″ / 3.2 mm Beads (Standard for 4″ / 10 cm Cove Base)
Units	30-oz cartridge (950.4 grams) Quart (946 ml) Discontinued 9/1/15 Gallon (3.78 L) 4 Gallon (15.14 L)
Open Time	None recommended
Working Time	Up to 15 minutes
Shelf Life	One year, unopened
Freeze/Thaw Stable	Yes, to 10°F (-12° C)
VOC Content	Zero g/L; calculated and reported, SCAQMD 1168
Clean Up	Wet– clean, white cloth with neutral detergent and water Dry– clean, white cloth and mineral spirits
Walls	Structurally sound and dry wall surfaces
Advantages	Moisture and alkali resistant Good wet strength Excellent bond integrity Versatile (use for rubber or vinyl wall base) AGIS Guarantee Nonflammable